I'm marshal here's a walk through our entire shop, starting with power, infrastructure and infrastructure. Ok, this is the shop 4,000 square feet, our new CB construction right here about 12 base on the inside, basically posts on 16-foot centers, let's start with the power so right now what we have for the workshop got a two kilowatt: condo generator, a big battery bank 72 volts, 800m powers. This is an inverter of four kilowatts for the main house. This is a stackable inverter that does not work. This is a 240-volt inverter.

We can't figure how to make it work. This inverter is for the house and some shop power at 120. Volts here are bus bars from the big battery bank. This these are the 2 36 volts, a piece we're going to use them at 72 volts. This is our breaker box here.

Here's the here where the old plug is for the 240 volt outlet for the welders, okay, so that's basic power. Here's our chargers that we use right now and we're getting a charger and an inverter, a 72, volt, inverter 10 kilowatts, 240 volts should be coming this weekend, as well as a 2 120, volt, 10 kilo, watt, inverter and a charger in about a week. Okay, so some of the equipment here we're going to have two tractors. This is one with two power cubes and actually be testing this one out and shipping.

It there's another one back here as far as tractor power and we're going to be shipping one and receiving one back from James and Texas okay more about the power infrastructure. This is for welder power right now, we're using a a PTO generator and I'm going to show the other tools in the other workshop. But this is a PTO generator run by a hydraulic motor right off the power cube from the tractor. Okay, cooling. We've got a big lathe.

We're going to convert this actually two hydraulic run because we're going to have hydraulic take off here we're going to mount a dismountable hydraulic motor in here. That's going to be our life Big naive! These are okay, actually I, see more power. Electronics. Here, that's a three phase converter with its control box. That's being hung up we're using that right now, too, from the power take-off generator to power. These three phase mills and surface grinders, so these are Mel's Bridgeport's, surface grinder park and majestic another Mel Briana's working on a an iron worker.

This is the upper arm. This is the type of shelving that we're putting up. We've got a whole bunch of this. In the workshop you see. All those shelves back here is what we have. That's all waiting to be assembled and organized properly.

Here are some more welding infrastructure. We've got this Hobart mega mega. That's three phase not connected yet use a torch, set shop, lights, ironworker, proper, a broken power tube that need some modifications. We also have a 350, 500 watt generator. Here's the old tractor, where we're replacing the power cube right now, actually we're fixing it up into the engine mounts broke off, so there's mag drill.

We've got two of those grinder a couple grinders like that in a big, bigger, 15, amp grinder, two of them, one that works in one, that's without a power cord, so our tool chests who's here are cylinders a little bit of storage shelf. This is a CB press. It's going to go out! Ok, millermatic, 200, welder! We've got two of those one, that's actually the air solenoid gas song is being replaced in a small, tiny welder. This is a little 120 volt 90 m wire welder. This is a broken over last night.

Rapini inverter technology, plasma cutter I think this. This can possibly work. If we get a new gun for it, it doesn't work right now. We've got a small one, 80 amp stick welder we've got some Milwaukee cordless drills. These are really nice. Actually, we got four of these very nice. They work well lightweight.

One work table here for welding little bench, top grinder, there's a voice for minor lifting heavier hoist right here this. This one could lift about 2,000 pounds or max like 2500 and you're, pushing the limits there. Okay, shelf space, scrum board power cube. That's not working this one's got a problem, so the count and power cubes is one here, one, that's on a tractor, that's being replaced and the third one, the Jose's working on and another engine power cube. That's needs to be modified thoroughly. Okay, that's the basic workshop infrastructure, other tools.

Let's talk about some other power tools, so get our welding helmets. We've got like three of those. A quickie saw the gas power to freak. You saw. We've got the second mag drill here, some power tools. This is some of our organizational space. We got a blower, some organized space, okay, so here's basically circular saw court corded drills, that's the big grinder that the team needs a power cord there's this grinder works here. So we've got two more of these grinders.

This is a reciprocating, saw, odds and ends here. That was the first circuit mill, so a metal cut off saw right here. Here's a small lathe, here's, a woodcut up saw small metal band, saw shop compressors two of them this one. This one works, I think it just needs a new cord and that's about it for the main workshop here. Let me know if you have any questions. I can take up some more take some more details. Well, that's basically, a pretty decent, decent sized space where we are doing all the work.