Home
Contribute
Contact Us
Browse all meetings
Home
Contribute
Contact Us
Browse all meetings
Open Source Ecology
/
Solenoid Driver Etching
/ 7 Dec 2011
Open Source Ecology
/
Solenoid Driver Etching
/ 7 Dec 2011
Previous Meeting
Next Meeting
⏯
Sync
Add meeting
Rate page
Subscribe
►
From YouTube:
Surface mount 10
Description
Gofigoig
A
Actually take the transferred, this is just water and we're going to lose soaked for how long.
A
Let me take it inside, take it inside one minute.
A
It's okay in here.
A
Okay, so that's one minute right: there.
B
At the two-minute mark, let's start removing.
A
The ice on the top yeah, let's go.
A
You got some tape.
Is that the kind of tape used this blue is any difference between the blue, another one.
So it's mystical this.
C
Is general masking tape?
You know what painter used to cover.
Why do.
A
That yeah it's two minutes.
Let's see what happens.
A
No, that's poor, transfer, I think the toner is think that we're just simply low on toner.
B
Yes,.
C
Would you say.
B
When I wasn't to know.
A
That you work- and it was yours, pretty I- mean.
C
It a solid it's like on that skin, your stuff, like.
B
Apparently, if you overdo the ironing process, you can stick the gloss.
You.
A
Can log grip.
B
Board- and it makes it tougher to remove the glossy paper afterwards, if you like too much eat for 6-10, for you to tongue.
A
You're gonna run into town, real, quick and get a better print or you think that's I.
C
Think the price well I mean because you know a lot of these are good.
Let me know you know ahead of that head, but yeah.
A
But I mean what about the ones that are missing so we're.
C
Going.
A
To just basically yeah.
C
Match them.
A
And then scratch them now.
C
We have to read, transfer it, but I.
C
Still it's like like what would you guys do when I gone did you did you have it flat on there and.
A
Then, how much of the ledge you did with the edge to ya did seriously with the edge afterwards we had a three minutes flat, then after that solid for like seven minutes more, is that too much.
C
Yeah looks good.
C
Mm-Hmm just might have been.
You got this side cuz the other side.
Not you know, yeah, it's just the corner.
You could freak it.
A
What the circuit mall would be.
C
Better yeah there's.
B
No, no.
C
Mistakes of the circum.
C
Yeah I mean it says, good sucks.
If you missed a little bit.
C
Water is cold.
A
Does the cup clapboard and then stay in the water for a long time or I'll, see why not you did yes, if you just let it stay.
C
There we'll come on.
C
Yeah 9280, whatever eighty ninety percent of some reason, parts of it there there but.
A
I would say the printer to men, I think the printer to is I, don't know it just I mean this is I.
C
Mean this is yeah, that's great, you know, that's fine, but might be so uneven, but.
A
At the same time, the print I saw the print I, don't think the print was totally even yeah.
C
Maybe.
C
It's like me, I get all this in here.
C
These are kind of a problem area.
C
Oh.
C
Ok, you can you want to clean these off and will breed transfer yeah.
A
Yeah I mean: do we want to me.
C
Maybe maybe I should I earn one yeah.
A
You do that I'll kind of jiggle I, remember yep, when, let's see, if you can do it differently, ok, so there's some failure, point some some points or just not as properly not transferred rather.